dragspecialties.eu / partseurope.eu WINDSHIELDS & FAIRINGS SADDLEBAGS & LUGGAGE SEATS & SISSY BARS FUEL/AIR SYSTEMS EXHAUST TRANSMISSION, CLUTCH LINE & DRIVELINE ENGINE GASKETS & SEALS LIGHTING & LICENSE PLATES ELECTRICAL HANDLEBARS, CONTROLS & MIRRORS CABLES TANKS & OIL FILTERS BRAKES & BRAKE LINES DASHES & GAUGES FENDERS COVERS, LOCKS & GENERAL AUDIO, COMMUNICATION & MOUNTS FRAMES & SUSPENSION FOOTRESTS & FLOORBOARDS WHEELS & AXLES DISCLAIMER: SEE PAGE 5 FOR IMPORTANT INFORMATION REGARDING CERTAIN WARRANTY AND EMISSION CONTROL REGULATORY COMPLIANCE INFORMATION. SECTION 4 See OLDBOOK For Early Model Applications All part numbers in BLUE are new for 2026. 455 PART # DESCRIPTION 1020-1479 For late-model European spec models w/ active intake and exhaust ACTIVE INTAKE AND EXHAUST ELIMINATOR KIT •Used to avoid setting a diagnostic trouble code when installing some aftermarket air filters and exhaust that require the removal of original equipment active systems; for off-road racing use only PART # DESCRIPTION WELD-IN SENSOR BUNGS 1861-0831 18 mm x 1,5 stainless steel 7806-1563 18 mm x 1,5 steel SOCKET PLUGS 1861-0832 12 mm x 1,25 steel 1861-0833 18 mm x 1,5 stainless steel O2 SENSOR WELD-IN BUNGS AND PLUGS •Allow for easy installation of oxygen sensors •Sold each PART # DESCRIPTION STRAIGHT 1861-0561 12 mm x 1,25 1861-05601 18 mm x 1,5 PART # DESCRIPTION 45° ANGLE 1861-0695 12 mm x 1,25 1861-0694 18 mm x 1,5 1 Stainless steel. O2 WELD-IN SENSOR BUNGS •Used to install O2 sensors in exhaust systems •Weld-in style •Available in 12 x 1,25 mm or 18 x 1,5 mm styles •Available in a standard straight style, or machined at a 45° angle •Sold in pairs PART # DESCRIPTION 1861-0728 O2 sensor bung, plug and washer kit O2 SENSOR BUNG, PLUG AND WASHER KIT •Weld-in O2 sensor bung allows installation of O2 sensors in most exhaust systems; 18 mm x 1,5 PART # DESCRIPTION 1861-0562 12 x 1,25 mm PART # DESCRIPTION 1861-0496 18 x 1,5 mm O2 SENSOR PORT PLUGS •Works with any O2 sensor port fitting •Two sizes available: 18 x 1,5 mm or 12 x 1,25 mm •Sold each PART # DESCRIPTION 1861-0791 12 mm x 1,25 PART # DESCRIPTION 1861-0790 18 mm x 1,5 O2 SENSOR PORT PLUGS •Allow non-sensor H-D models to run newer-style exhaust systems equipped with O2 sensor ports •Simply screw into non-essential sensor ports •Sold in pairs PART # DESCRIPTION 1861-0607 12 mm x 1,25 PART # DESCRIPTION 1861-0464 18 mm x 1,5 O2 SENSOR PORT PLUG KITS •Allow select pre-closed-loop H-D models to run newer-style exhaust systems equipped with O2 sensor ports •Include two zinc-plated plugs with sealing washers •Simply screw into nonessential sensor ports PART # DESCRIPTION 1861-1185 O2 port bushing adapter O2 PORT BUSHING ADAPTER •Reduce the O2 port from 18 mm to 12 mm PART # DESCRIPTION 1861-0784 O2 port bushing adapters O2 PORT BUSHING ADAPTERS •Threaded outer and inner adapters reduce O2 sensor port from 18 mm to 12 mm, allowing riders to use our exhaust pipes on select, newer-model motorcycles •Sold in pairs 1861-0831 1861-0832 1861-0496 1861-0790 1861-0607 1861-0464 1861-0694 1861-0560
RkJQdWJsaXNoZXIy ODQ0NDEw