dragspecialties.eu / partseurope.eu WINDSHIELDS & FAIRINGS SADDLEBAGS & LUGGAGE SEATS & SISSY BARS FUEL/AIR SYSTEMS EXHAUST TRANSMISSION, CLUTCH LINE & DRIVELINE ENGINE GASKETS & SEALS LIGHTING & LICENSE PLATES ELECTRICAL HANDLEBARS, CONTROLS & MIRRORS CABLES TANKS & OIL FILTERS BRAKES & BRAKE LINES DASHES & GAUGES FENDERS COVERS, LOCKS & GENERAL AUDIO, COMMUNICATION & MOUNTS FRAMES & SUSPENSION FOOTRESTS & FLOORBOARDS WHEELS & AXLES DISCLAIMER: SEE PAGE 5 FOR IMPORTANT INFORMATION REGARDING CERTAIN WARRANTY AND EMISSION CONTROL REGULATORY COMPLIANCE INFORMATION. SECTION 5 See OLDBOOK For Early Model Applications All part numbers in BLUE are new for 2026. 459 PART # DESCRIPTION 1020-4284 ECM refurbishing license for Centurion Super Pro ECM REFURBISHING LICENSE FOR CENTURION SUPER PRO •With the H-D ECM refurbishing license, you can refurbish used ECMs and keep your customer’s HarleyDavidson motorcycles operating at their best •Enables a wide range of refurbishing capabilities like converting a XL1200 ECM for an XL883, adapting a Twin-Cooled ECM for an air-cooled engine or retrofitting a 07 ECM to a 01-05 model •Modify the VIN on a used ECM to match your customer’s Harley-Davidson •Restore and update the ECM to OEM/stock calibration, ensuring the motorcycle operates as if it were new •ECM automatically updates its configuration to match stock settings, eliminating manual setup hassle •Simple and straightforward requirements: verify that the ECM is compatible with the target vehicle model, maintain an up-to-date Centurion Super Pro license to ensure software compatibility/ support and purchase a license for each ECM refurbishment job NOTE: Does not clear the pre-existing odometer reading in the ECM. The higher of the odometer readings from the ECM or the speedometer will be synchronized and adopted by both. NOTE: TechnoResearch service does not unlock ECMs that are secured against modifications. NOTE: Any custom tuning or calibrations previously applied will NOT be retained after refurbishment; only OEM calibrations are restored. PART # DESCRIPTION 1020-3222 USB Direct Link (ea.) USB DIRECT LINK LICENSE •USB key including one license PART #1020-2852 •Maximize the performance of Harley-Davidson fuel-injection •Requires Centurion hardware - VCM-TR4 •Can be used on one motorcycle an unlimited amount of times, but not multiple motorcycles •No return •Sold each PART # DESCRIPTION 1020-2852 Additional digital tuning license for PART #s 3807-0314 and 1020-2851 DIGITAL DIRECT LINK LICENSE •For Centurion Super Pro Plus or VCM-TR4 •Can be used on one motorcycle an unlimited amount of times, but NOT multiple motorcycles •No inventory to stock •Buy as you go •Cost effective •Save time and money •Sold each NOTE: Licenses cannot be returned. PART # DESCRIPTION 3807-0498 Centurion Super Pro Plus diagnostics USB license key CENTURION SUPER PRO PLUS DIAGNOSTICS USB LICENSE KEY •The Centurion Diagnostics USB license key is needed to run the Centurion Super Pro Plus (H-D, Victory and Indian) diagnostic software •It permits communication with 1995-2020 Harley-Davidson and Buell models using the proprietary VCM-TR4 Communication Module and cables NOTE: Annual new model year updates available for download and purchase for minimal fee; see licensing for details. PART # DESCRIPTION 1020-2868 TechnoResearch USB key upgrade TECHNORESEARCH USB KEY UPGRADE •Upgrade of non-EU TechnoResearch performance products to be able to use European licenses and provide access to other TechnoResearch products where no master key was provided •PART #1020-2868 upgrades Centurion Tuner without tuning capabilities (VCM-TR3 and VCM-TR4) to enable tuning capabilities for all Harley-Davidson Delphi EFI systems (additional European digital tuning license PART #1020-2852 required; sold separately, see above) PART # DESCRIPTION 3850-0449 O2 install block PART # DESCRIPTION 3850-0450 Vent screw O2 INSTALL BLOCK AND VENT SCREW • Block is designed to be compatible with 18 mm wideband O2 sensors •Block will be temporarily attached to the motorcycle using Rivnut/rivet nuts and a vent screw •If using this block, please ensure you have the proper tools to allow for rivet nut installation •It is recommended that you purchase these blocks in pairs (one for each cylinders exhaust) •Vent screw is a replacement part to be used with the O2 install block •Vent screw is a hollowed out bolt that holds the install block in the Rivnut/rivet installed by the O2 installation kit 3850-0450 3850-0449
RkJQdWJsaXNoZXIy ODQ0NDEw