www.zodiac.nl 26-063 6132 B2 JACK CENTER STAND An easy to use bike stand that can be used for storing or servicing your V-Twin. It is placed under the lower frame tubes and uses a handle to tilt the stand over. Stand is 9" (230 mm) high, enough to lift the rear wheel from the ground for easy chain or belt tensioning, rear brake service or rear wheel removal. Two piece construction made from heavy gauge zinc coated steel and covered with a high density plastic tube to prevent the frame paint from damaging. 721697 B2 Easy-Lift bike stand 6131 B2 PRODUCTS REAR MOVER No more lifting when parking your Harley, Victory, Indian or any other make heavyweight cruiser in places were space is limited. Simply back-up your bike onto the Rear Mover and it can be moved around so easily it's almost unbelievable. It can be pushed through narrow corners and turned 180° without any hassle. Also great for easy cleaning. Works with 150 through 260 wide tires. 721698 B2 Products rear mover Accessories 770901 Manual operated wheel clamp 770902 Mechanical operated wheel clamp 770904 Pneumatic wheel clamp 770905 Air hose connection kit for ZPN 770904 770906 Quickmount/dismount kit for ZPN 770902 or 770904 on Goldrake Workshop lift 770903 Automatic ride-in style wheel clamp (also great for in a van or trailer) 770907 Quickmount/dismount kit for ZPN 770903 on Goldrake Workshop lift 770908 Hand held battery operated up-and-down remote control unit with receiver unit 770909 Up-and-down foot control 770910 Set of left and right tie-down eyelet side rails, 220cm 770911 Skid plate, aluminum, 54x34cm 770912 Set of left and right 27.5x132cm side extensions with 24.4x70cm retractable ramps for trikes 770913 Retractable front platform extension 75x35cm for extremely long bikes 32057 ZODIAC GOLDRAKE MOTORCYCLE WORKSHOP LIFT BY LV8 Designed and made in Europe professional electro-hydraulically operated motorcycle lift for use with Heavy-Weight motorcycles. Comes complete with electro-hydraulic unit with hand control unit, retractable gate, ramp, front safety bar, left and right tool holders and safety device to block the platform. Various accessories are available to completely adapt the lift exactly to your needs. Lift and accessories are drop shipped at cost to your address. • Capacity: 800kg • Single-phase: 220-240 Volt • Minimum height: 18cm • Maximum height: 130cm • Platform width: 75cm • Platform length: 220cm • Ramp width: 45cm • Ramp length: 57.5cm • CE and TÜV approved 770900 Zodiac Goldrake Workshop Lift 6129 PINGEL PERMANENT WHEEL CHOCK The Pingel wheel chocks are also available with drilled mounting holes. They mount permanently on the floor of your truck or trailer. The wheel chock is made from heavy duty thick wall steel construction and includes mounting hardware for easy installation. Available in 2 dimensions. These wheel chocks are a trademark of Pingel Enterprises Inc. and are made in the USA. 236346 3 1/2" Wide, takes wheels with up-to 3 1/2" wide tires 236348 6 1/2" Wide, takes wheels with up-to 6 1/2" wide tires (150/160mm) 6128 PINGEL REMOVABLE WHEEL CHOCK The Pingel wheel chock secures a motorcycle in your van, truck or trailer, and features a quick and easy removal. The wheel chock is made from heavy duty thick wall steel construction and includes a near-flush floor mounting hardware for easy installation and removal. The wheel chocks are available in 2 dimensions: 3 1/2" and 6 1/2" wide. Extra wheel chock mounting hardware is separately available to enable the location of the wheel chock in alternate locations. There is also a mounting plate available that will take 3 1/2" or 5 1/2" wide wheel chocks. These wheel chocks are a Trademark of Pingel Enterprises Inc. and made in the USA. 236342 3 1/2" Wide, takes wheels with up-to 3 1/2" wide tires (8.5cm) 236344 6 1/2" Wide, takes wheels with up-to 6 1/2" wide tires (13.5cm to 16.5cm) 236345 Extra wheel Chock mounting hardware (pair) 236349 Wheel chock mounting plate 3 1/2" and 5 1/2" Motorcycle Lift TOOLS & CHEMICALS
RkJQdWJsaXNoZXIy ODQ0NDEw