www.zodiac.nl 14-004 PRIMARY & CLUTCH CONTROL CABLES & HYDRAULIC LINES OIL, OIL FILTERS & OIL COOLERS SEAT TRANSMISSION FOOT CONTROLS HARDWARE EXHAUST GASKET & SEALS FRONT FORKS WINDSHIELD ELECTRIC & LIGHT FINAL DRIVE FRAME & REAR SUSPENSION LUGGAGE ENGINE ELECTRICS WHEELS & TIRES FENDER & STRUTS TOOLS & CHEMICALS INTAKE BRAKE GAS- & OIL TANK TECH TIPS & CROSS REF OEM>ZPN ENGINE HANDLEBAR, HAND CONTROLS & MIRRORS GAUGES & DASHES ALPHABETICAL INDEX HELMETS, LUGGAGE, AUDIO & MORE 33951 ONE INCH TWOPIECE ELECTRA GLIDE STYLE BUCKHORN BAR Exact copy of the 1" diameter two-piece Buckhorn handlebar originally found on 1975-1979 Electra Glide. Also fits 1960-1974 models when converted from internal throttle to normal twist grip style throttle. Two-piece handlebars must always be installed with a one-piece handlebar top clamp. A=Rise=5 1/2" (14cm), B=End rise=2 1/2" (6.4cm), C=Width=29" (74cm), D=Center width=7 7/8" (20cm), E=Base width 10" (26cm), F=Pull back=9" (23cm), G=Knurles=2" (5cm), no dimples 735080 Two-piece Buckhorn bar (OEM 56044-75 & 56056-75) ´ 781186 Springer fork top clamp for 1936 thru 1945 style in-line forks, chrome 781187 Springer fork top clamp for 1946 thru 1948 offset forks, chrome 30807 RISERS AND UPPER TRIPLE TREES FOR EARLY SPRINGER FORKS These risers allow you to install any of our 1" or larger diameter handlebars on the special triple tree clamps on stock 1936 thru 1948 style front forks and consequently also on our Old Style Springer forks. The Flanders style risers feature rubber inserts to minimize handlebar vibrations. A. 745876 Dog Bone riser set, 4" (10cm) rise B. 745878 Flanders Style riser set, 4" (10cm) rise and 2" (5cm) pullback C. 745875 Top fork clamp to fit Dog Bone or Flanders Style risers on Off-set forks D. 745877 Top fork clamp to fit Dog Bone or Flanders Style risers on In Line forks 782142 Springer fork top clamp for 1946 thru 1948 offset forks, satin nickel finish 30806 VTWIN TRIPLE TREE CLAMPS FOR EARLY SPRINGERS These Springer triple tree clamps will fit stock 1936 thru 1948 style front forks as well as our replica Old Style Springer fork. Clamps take dog bone style risers and are available for in-line or offset fitment. Matching S&H short spirals 789289 Push type short spiral (short version of OEM 56245-35 & 3312-35) 789290 Pull type short spiral (short version of OEM 56246-35 & 3312-35A) 32123 STELLING & HELLING SPEEDSTER HANDLEBARS FOR SPRINGER FORKS Jack Tracey, life-long member and President of the world's oldest motorcycle club, the Yonkers Motorcycle Club and owner of the Harley-Davidson dealership in Yonkers (NY) asked Stelling & Helling to develop handlebars taller than the original "comfortable" Speedster bars. S&H came up with these ones with horn and dimmer switch mount holes on the left side and a shortened grip area for use with the short Hellings type spirals. These bars are made for in-line Springer forks with the outer holes measuring 4 3/4" (120.7mm) center to center and come complete with parkerized end plugs. Order pinch bolts and two short spirals separately. Grips must be cut to length for this installation. "In-line" forks were originally made for 1936-1940 Big Twin with 28° frame neck, 1941-1945 Big Twin with 29° frame neck, 1929-1957 45CI Solo and 1937-1957 Servi-Car. Offset forks were stock on 1946-1948 EL and FL Big Twin with the 30° frame neck as well as most reproduction rigid frames with stock 30° neck. 4" (10cm) rise S&H Speedster manillares A=10cm, B=7.5cm, C=85cm, D=32cm, F=15cm 789287 Chrome for 1929-1957 style in-line Springer forks 789288 Chrome for 1946-1948 offset Springer forks HANDLEBAR, HAND CONTROLS & MIRRORS One Inch Diameter Handlebars
RkJQdWJsaXNoZXIy ODQ0NDEw